amplifiers - smt 5 5 - 486 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com hmc487lp5 / 487lp5e surface mount phemt 2 watt power amplifier, 9 - 12 ghz v01.0705 general description features functional diagram the hmc487lp5 & HMC487LP5E are high dynamic range gaas phemt mmic 2 watt power ampli ers housed in leadless 5 x 5 mm surface mount packages. operating from 9 to 12 ghz, the ampli er provides 20 db of gain, +33 dbm of saturated power and 20% pae from a +7.0 v supply voltage. output ip3 is +36 dbm typical. the rf i/os are dc blocked and matched to 50 ohms for ease of use. the hmc487lp5 & HMC487LP5E eliminate the need for wire bonding, allowing use of surface mount manufacturing techniques. saturated power: +33 dbm @ 20% pae +36 dbm output ip3 20 db gain +7.0 v @ 1300 ma supply 50 ohm matched input/output 25 mm 2 leadless smt package electrical specifications, t a = +25 c, vdd1, 2, 3, 4, 5 = +7v, idd = 1300 ma* typical applications the hmc487lp5 / HMC487LP5E is ideal for use as a power ampli er for: ? point-to-point radios ? point-to-multi-point radios ? test equipment and sensors ? military end-use parameter min. typ. max. min. typ. max. units frequency range 9 - 11 11 - 12 ghz gain 17 20 19 22 db gain variation over temperature 0.05 0.07 0.05 0.07 db/ c input return loss 7 15 db output return loss 7 15 db output power for 1 db compression (p1db) 29 32 28 31 dbm saturated output power (psat) 33 32 dbm output third order intercept (ip3) 36 35 dbm noise figure 98db supply current (idd)(vdd = +7v, vgg = -0.3v typ.) 1300 1300 ma * adjust vgg between -2 to 0v to achieve idd = 1300 ma typical.
amplifiers - smt 5 5 - 487 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com p1db vs. temperature broadband gain and return loss gain vs. temperature psat vs. temperature -25 -20 -15 -10 -5 0 5 10 15 20 25 6 7 8 9 10 11 12 13 14 15 s21 s11 s22 response (db) frequency (ghz) -25 -20 -15 -10 -5 0 8 8.5 9 9.5 10 10.5 11 11.5 12 12.5 13 +25 c +85 c -40 c return loss (db) frequency (ghz) -20 -15 -10 -5 0 8 8.5 9 9.5 10 10.5 11 11.5 12 12.5 13 +25 c +85 c -40 c return loss (db) frequency (ghz) 24 25 26 27 28 29 30 31 32 33 34 35 36 8 8.5 9 9.5 10 10.5 11 11.5 12 12.5 13 +25 c +85 c -40 c p1db (dbm) frequency (ghz) 24 25 26 27 28 29 30 31 32 33 34 35 36 8 8.5 9 9.5 10 10.5 11 11.5 12 12.5 13 +25 c +85 c -40 c psat (dbm) frequency (ghz) 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 8 8.5 9 9.5 10 10.5 11 11.5 12 12.5 13 +25 c +85 c -40 c gain (db) frequency (ghz) input return loss vs. temperature output return loss vs. temperature hmc487lp5 / 487lp5e surface mount phemt 2 watt power amplifier, 9 - 12 ghz v01.0705
amplifiers - smt 5 5 - 488 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com gain power and oip3 vs. supply voltage @10.5 ghz gain, power and oip3 vs. supply current @ 10.5 ghz output ip3 vs. temperature power compresion @ 10.5 ghz noise figure vs. temperature reverse isolation vs. temperature 10 14 18 22 26 30 34 38 42 8 8.5 9 9.5 10 10.5 11 11.5 12 12.5 13 +25 c +85 c -40 c oip3 (dbm) frequency (ghz) 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 -10 -8 -6 -4 -2 0 2 4 6 8 10 12 14 16 18 pout gain pae pout (dbm), gain (db), pae (%) input power ( dbm ) 18 20 22 24 26 28 30 32 34 36 38 40 6.5 7 7.5 gain p1db psat oip3 gain (db), p1db (dbm), psat (dbm), oip3 (dbm) vdd supply voltage (vdc) 18 20 22 24 26 28 30 32 34 36 38 40 42 800 900 1000 1100 1200 1300 gain p1db psat oip3 gain (db), p1db (dbm), psat (dbm), oip3 (dbm) idd supply current (ma) 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 8 8.5 9 9.5 10 10.5 11 11.5 12 12.5 13 +25 c +85 c -40 c noise figure (db) frequency (ghz) -70 -60 -50 -40 -30 -20 -10 0 8 8.5 9 9.5 10 10.5 11 11.5 12 12.5 13 +25 c +85 c -40 c isolation (db) frequency (ghz) hmc487lp5 / 487lp5e surface mount phemt 2 watt power amplifier, 9 - 12 ghz v01.0705
amplifiers - smt 5 5 - 489 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com vdd (vdc) idd (ma) +6.5 1330 +7.0 1300 +7.5 1285 typical supply current vs. vdd note: amplifier will operate over full voltage ranges shown above. vgg adjusted to achieve idd= 1300 ma at +7.0v. power dissipation* 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 -10 -8 -6 -4 -2 0 2 4 6 8 10 12 14 16 power dissipation (w) input power ( dbm ) 11 ghz max pdiss @ +85c absolute maximum ratings drain bias voltage (vdd1, 2, 3, 4, 5) +8 vdc gate bias voltage (vgg) -2.0 to 0 vdc rf input power (rfin)(vdd = +7.0 vdc) +20 dbm channel temperature 150 c continuous pdiss (t= 85 c) (derate 154 mw/c above 85 c) 10 w thermal resistance (channel to ground paddle) 6.5 c/w storage temperature -65 to +150 c operating temperature -40 to +85 c outline drawing * refer to thermal management for surface mount components application note herein. part number package body material lead finish msl rating package marking [3] hmc487lp5 low stress injection molded plastic sn/pb solder msl1 [1] h487 xxxx HMC487LP5E rohs-compliant low stress injection molded plastic 100% matte sn msl1 [2] h487 xxxx [1] max peak re ow temperature of 235 c [2] max peak re ow temperature of 260 c [3] 4-digit lot number xxxx notes: 1. leadframe material: copper alloy 2. dimensions are in inches [millimeters] 3. lead spacing tolerance is non-cumulative. 4. pad burr length shall be 0.15mm maximum. pad burr height shall be 0.05mm maximum. 5. package warp shall not exceed 0.05mm. 6. all ground leads and ground paddle must be soldered to pcb rf ground. 7. refer to hittite application note for suggested land pattern. package information hmc487lp5 / 487lp5e surface mount phemt 2 watt power amplifier, 9 - 12 ghz v01.0705 electrostatic sensitive device observe handling precautions
amplifiers - smt 5 5 - 490 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com pin number function description interface schematic 1-3, 5-8, 10-12, 14, 15, 17-20, 22-24, 26, 27, 29-31 n/c no connection required. these pins may be connected to rf/dc ground without affecting performance. 4 rfin this pin is ac coupled and matched to 50 ohms from 9 - 12 ghz. 9 vgg gate control for ampli er. adjust to achieve idd of 1300 ma. please follow mmic ampli er biasing procedure application note. external bypass capacitors of 100 pf and 2.2 f are required. 21 rfout this pin is ac coupled and matched to 50 ohms from 9 - 12 ghz. 32, 28, 25, 13, 16 vdd1, vdd2, vdd3, vdd4, vdd5 power supply voltage for the ampli er. external bypass capacitors of 100 pf and 2.2 f are required. gnd ground: backside of package has exposed metal ground slug that must be connected to ground through a short path. vias under the device are required pin descriptions application circuit component value c1 100 pf c2 2.2 f hmc487lp5 / 487lp5e surface mount phemt 2 watt power amplifier, 9 - 12 ghz v01.0705
amplifiers - smt 5 5 - 491 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com evaluation pcb item description j1, j2 sri pc mount sma connector j3, j4 2mm dc header c1 - c6 100 pf capacitor, 0402 pkg. c7 - c12 2.2f capacitor, tantalum u1 hmc487lp5 / HMC487LP5E ampli er pcb [2] 108188 evaluation pcb [1] reference this number when ordering complete evaluation pcb [2] circuit board material: rogers 4350. list of materials for evaluation pcb 108190 [1] the circuit board used in th is application should use rf circuit design techniques. signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. a suf cient number of via holes should be used to connect the top and bottom ground planes. copper lled vias under the device are recommended. the evaluation board should be mounted to an appro- priate heat sink. the evaluation circuit board shown is available from hittite upon request. hmc487lp5 / 487lp5e surface mount phemt 2 watt power amplifier, 9 - 12 ghz v01.0705
|
